(888) 686-8265 Lowest Prices Best Shipping Rates

4" Round Leaf Eater Ultra Rain Head

4" Round Leaf Eater Ultra Rain Head
Images may be inaccurate. See specs table below to ensure accuracy.
Minimal maintenance required
Pivot the outlet to suit vertical or horizontal downspout
Maximises the catchment efficiency at low and high flow rates
Include adaptor for secure connection to downspout
Modern, sleek design the ultimate in Rain Heads
$63.99
Description

Details

Rain Harvesting Leaf Eater Ultra™, part# RHUL98 is the next generation Rain Head, featuring the new Hydro Activated Filtration technology and VH Pivot™ outlet. The Leaf Eater Ultra™ Rain Head prevents debris from entering the Rain Harvesting system, improves water quality and reduces tank/cistern maintenance. The Leaf Eater Ultra™ uses the Leaf Slide which deflects debris away from the screen and a precisely angled screen which directs leaves and debris away from the flow of water to maximize catchment efficiency. This Rain Head also incorporates a VH Pivot™ outlet that swivels to suit vertical or horizontal downspouts. The Leaf Eater Ultra™ can also be used as a debris removing device even when rainwater is not being collected.

Leaf Eater Ultra Pivot

Installation Instructions

1.  Remove and discard the cap.

2.  Fit the adaptor to the bottom of Leaf Eater Ultra™ outlet.

3.  Measure and remove 12″ of downspout from the bottom of the gutter outlet. Ensure all edges are clean and smooth.

4.  Remove the front cover by unscrewing the two screws with a phillips head screwdriver.

5.  Insert the Leaf Eater Ultra™ by sliding the outlet into the bottom section of downspout.

6.  Screw the Leaf Eater Ultra™ into position through the screw slots provided. Ensure appropriate screws and anchors (if required) are used.

7.  Check the placement of the Vibrating Screen. It must sit behind and below the front face (refer figure 1).

8.  Insert the Leaf Slide into slot holes (refer figure 2).

9.  Re-install the front cover by reinserting the two screws.

Mid-Mount Installation

1.  Fit the adaptor to the bottom of Leaf Eater Ultra™ outlet.

2.  Measure and remove 12″ of downspout from where Leaf Eater Ultra™ is to be situated. Ensure all edges are clean and smooth.

3.  Remove the cap and use snips to remove a section to fit the appropriate downspout.

4.  Remove the front cover by unscrewing the two screws with a phillips head screwdriver.

5.  Slide the cap up the top section of downspout and hold temporarily in place.

6.  Insert the Leaf Eater Ultra™ by sliding the outlet into the bottom section of downspout. The back fixing plate must sit behind the top section of downspout.

7.  Screw the Leaf Eater Ultra™ into position through the screw slots provided. Ensure appropriate screws and anchors (if required) are used.

8.  Check the placement of the Vibrating Screen. It must sit behind and below the front face (refer figure 1).

9.  Insert the Leaf Slide into slot holes (refer figure 2).

10.  Re-install the front cover by reinserting the two screws.

11.  Slide the cap back down the downspout until it sits securely on the top of the Leaf Eater Ultra™.

Horizontal (Rear Outlet) Installation

1.  If installing under gutter remove and discard cap. If installing mid-mount carefully use snips to remove a section of cap to fit the appropriate downspout.

2.  Swivel the outlet to the horizontal position – some force may be required. Fit the adaptor to the bottom of Leaf Eater Ultra™ outlet.

3.  Remove the front cover by unscrewing the two screws with a phillips head screwdriver.

4.  Position the Leaf Eater Ultra™ next to the existing downspout, mark and cut top and bottom cut lines. Ensure all cut edges are clean and smooth.

5.  Slide the cap up the top section of downspout and hold temporarily in place.

6.  Insert the Leaf Eater Ultra™ by sliding the rear outlet into the horizontal pipe. The back fixing plate must sit behind the top section of downspout.

7.  Screw the Leaf Eater Ultra™ into position through the screw slots provided. Ensure appropriate screws and anchors (if required) are used.

8.  Check the placement of the Vibrating Screen. It must sit behind and below the front face (refer figure 1).

9.  Insert the Leaf Slide into slot holes (refer figure 2).

10.  Re-install the front cover by reinserting the two screws.

11.  Slide the cap back down the downspout until it sits securely on the top of the Leaf Eater Ultra™.

Leaf Eater Ultra Installation Image

Show More

Size Comparison

image of man
At Scale
Specifications

Additional Information

Store ID X4724127
Manufacturer Info
Product Part # RHUL100
Former MPN's RHUL98
Manufacturer Rain Harvesting
Installation Instructions Rain Harvesting Installation Instructions
Brochure Rain Harvesting Product Specifications
Physical Features
Weight (lbs) 3
Dimensions 9" Length x 8" Width x 17.5" Height
Color Natural White
Product Type Leaf Eater
Shipping Info
Shipping Locations California
Shipping Zip Codes 60504
phone
live chat
find tank